Configure OSPF Juniper SRX


Quick page to remind me how to configure OSPF on SRX's as its been a while.

#############
# R1 #
#############
set interfaces ge-0/0/0 unit 0 family inet address 10.0.0.1/30
set interfaces ge-0/0/1 unit 0 family inet address 192.168.0.1/24
set interfaces lo0 unit 0 family inet address 1.1.1.1/32

set routing-options router-id 1.1.1.1

set protocols ospf area 0.0.0.0 interface ge-0/0/0.0

set security zones security-zone TRUST interfaces ge-0/0/0.0 host-inbound-traffic system-services ping
set security zones security-zone TRUST interfaces ge-0/0/0.0 host-inbound-traffic system-services traceroute
set security zones security-zone TRUST interfaces ge-0/0/0.0 host-inbound-traffic system-services ssh
set security zones security-zone TRUST interfaces ge-0/0/0.0 host-inbound-traffic protocols ospf

set security zones security-zone TRUST address-book address BAML 159.5.153.0/24
set security zones security-zone TRUST host-inbound-traffic system-services all
set security zones security-zone TRUST host-inbound-traffic protocols all
set security zones security-zone TRUST interfaces ge-0/0/0.0

#############
# R2 #
#############

set interfaces lo0.0 family inet address 2.2.2.2/32
set interface ge-0/0/0.0 family inet address 10.0.0.2/30
set interface ge-0/0/1.0 family inet address 192.168.1.1/24

set routing-options router-id 2.2.2.2
set protocols ospf area 0.0.0.0 interface ge-0/0/0

set interfaces ge-0/0/0 unit 0 family inet address 10.0.0.1/30
set interfaces ge-0/0/1 unit 0 family inet address 192.168.0.1/24
set interfaces lo0 unit 0 family inet address 1.1.1.1/32
set routing-options router-id 1.1.1.1
set protocols ospf area 0.0.0.0 interface ge-0/0/0.0
set security zones security-zone TRUST interfaces ge-0/0/0.0 host-inbound-traffic system-services ping
set security zones security-zone TRUST interfaces ge-0/0/0.0 host-inbound-traffic system-services traceroute
set security zones security-zone TRUST interfaces ge-0/0/0.0 host-inbound-traffic system-services ssh
set security zones security-zone TRUST interfaces ge-0/0/0.0 host-inbound-traffic protocols ospf

Comments

Post a Comment

Popular posts from this blog

Image
VXLAN - GNS3 (VEOS \ IOU_L3)  Images:  Spine - IOU - i86bi_linux-adventerprisek9-ms.152-4.M1" Leaf -  vEOS - 4.13.16M-3213248.41316M.1   This was my first crack at configuring VXLAN i used a combination of vEOS and IOS because that is closest to what I run in my production environment. The actual vxlan configuration is very easy its more about making sure the underlying connectivity is in place. You can build the same lab in GNS3 using the CSR router and EIGRP which should be simpler (I had some issues with route summarization). The most important thing to confirm before starting on the vxlan configuration is that you have full reachability between all the loopbacks. Anyway it worked for me next step is doing this with EVPN. ################# ## SPINE-1 ## ################# conf t ## GENERAL ## hostname SPINE-1 ip multicast-routing ## INTERFACES ## int e0/1 ip addr 10.0.11.1 255.255.255.252 int e0/2 ip add...
Read more

Upgrading JUNOS via USB

I borrowed this guide from Juniper but keeping it here incase i cannot find it going forward. You need to have a fat32 or smaller than 4gb partitioned USB flash disk.  Enter the shell as root: user@switch> start shell user root Password: root@switch% Before inserting the USB device, perform the following: root@% ls /dev/da* /dev/da0 /dev/da0s1c /dev/da0s2a /dev/da0s3 /dev/da0s3e /dev/da0s1 /dev/da0s1f /dev/da0s2c /dev/da0s3c /dev/da0s1a /dev/da0s2 /dev/da0s2f /dev/da0s3d Insert the USB drive in the USB port. The following output will be displayed: root@% umass1: TOSHIBA TransMemory, rev 2.00/1.00, addr 3 da2 at umass-sim1 bus 1 target 0 lun 0 da2: <TOSHIBA TransMemory 5.00> Removable Direct Access SCSI-0 device da2: 40.000MB/s transfers da2: 983MB (2013184 512 byte sectors: 64H 32S/T 983C) root@% ls /dev/da* /dev/da0 /dev/da0s1c /dev/da0s2a /dev/da0s3 /dev/da0s3e /dev/da0s1 /dev/da0s1f /dev/da0s2c /dev/da0s3c /dev/da2 /dev/da0s1a /dev/da...
Read more